Pattern Revisions LST141 - LST180

LST141 DOROTHY

  • Page 1, under ATTACH BOTTOM PANEL, Step 1: (an alternate label placement) Install a handmade label, centered, 1" below the top straight edge of one Exterior Bottom Panel
  • Page 2, under ATTACH SLIP POCKET, Step 1: With RSU, center.......

LST143 GWEN (CIRCLE) BAG

  • ©2020 Circle Bag (download only) 1/2" Test square added to the "Circle Bag" pattern on page 2

LST149 BETTE

  • Page 5 Assemble the Flap: Step 2....Sew together with 1/4" seam allowance.
  • Page 5 Assemble the Bag: Step 2....Sew together with 3/4" seam allowance. Trim seams to 1/4" wide.
  • Page 6 Assemble the Bag: Step 7...and align the raw edges, with elastic nearest to the base....

LST151 CASEY

  • ©2024 - 
    • Cutting Instructions for Main Fabric: Cut (1) 2" by 16" (5.1cm by 40.6cm) for Piece C (Connectors)
    • On page 2, under ATTACH EXTERIOR SLIP POCKETS: Step 2 and Figure 5, added tip: For crisp shaping, topstitch 9" (22.9) above the bottom edge.
    • On pages 2 & 3, under PREPARE CONNECTORS:
      • Step 2. Subcut Piece C into (2) 2-1/2" (6.4cm) and (2) 5-1/2" (14cm) long Connector pieces.
      • Step 3....fold the raw ends of the two shorter Connectors...
      • Step 5....fold the remaining two long Connectors...

LST152 LAUREN

  • Please refer to the pattern (page 3, SHAPE SIDE GUSSETS, Step 1) for the correct measurements mentioned at 6:50 in the video tutorial.

LST154 SACHI

  • Cut (1) 10" by 9" piece for Piece J (Zipper Pocket).
  • Cut (1) 10" by 9-3/4" piece for Piece K (Zipper Pocket).
  • Page 2, Step 1 of PREPARE FRONT: .... magnetic snap, centered 2-1/4" down....

LST157 FREE SOUL

  • Under materials and supplies, you will need 1 magnetic bar snap-earlier patterns may have omitted this.
  • Figure 27 updated to show RS of lining.
  • ASSEMBLE THE BAG headline updated.

LST159 BINDER POUCH

  • STS179x Grommets are no longer available, we recommended using STS323x

STS163 KATYE

  • MATERIALS & SUPPLIES: Contrast 2: 25" wide by 21"
  • CUTTING LAYOUTS: Contrast 2: Missing two Piece P Straps on layout.

STS164 EVELYN

  • One pattern piece A, main panel, you should only cut one of main fabric on fold, and on interfacing on fold. (Not two as pattern piece says)
  • Cutting Instructions Piece E tip should read: Do not cut if using a metal zipper end.
  • Cutting Instructions Piece J should read: Only cut if using grommet strap connectors: Cut (2) 1-1/2" by 14" for Piece J (Handles)
  • Page 4: Step 8 (in the right column) should read: .... remaining Piece H RSD.

LST169 CARLY

  • You will need a piece of clear vinyl 3" by 4"
  • Main Fabric - Cut (2) 2" by 18" ofr Piece A (Strap)
  • INSTALL ZIPPER & ID POCKET: After making the appropriate markings, please cut out "Zipper Slot" and "ID Window" appropriately. So, you would need to cut the rectangle you have marked for each the Zipper and the ID pocket.

LST170 JUNE

  • Under CUTTING INSTRUCTIONS; INTERFACING: Cut (2) 1-1/4" by 14" for Piece I (Zipper Pocket Gusset)
  • Back Cover, Mesh listing - if 27" wide - 3/8 yard

LST172 SOPHIE

  • Under Attach Card Pockets Step 2 Piece C centered 4-3/4" down from Flap edge of Piece A.
  • ©2024 Version
    • ASSEMBLE CELL CASE - 1.With WST, fold bottom edge of Piece A up 7" (17.8 cm), aligning and securing side edges with sewing clips. Topstitch both sides 1/8" (3mm) from raw edges.
    • Instructions following ATTACH CARD POCKETS:

LST173 ISLA

  • Materials & Supplies: you'll need 4-1/2 yards of 1-1/2" wide Cotton Webbing for the handles and adjustable strap.
  • Page 4, Step 6 in the italic note: Piece G should be Piece D