Pattern Revisions LST221 - LST260

LST222 SECRET GARDEN

  • Step 2 under ATTACH LEAVES should read: 2. Arrange remaining seven.....

LST225 WATCH PARTY

  • Typo on Page 3 of LST225 Watch Party, under the CUFF, SHAPE & ATTACH INTERFACING, Step1.... SHAPE CUFF & CONNECTOR TABS

LST227 SANDY

  • Back Cover, Mesh listing - if 27" wide - 1/4 yard
  • Page 2, under ASSEMBLE TOP BAND, Step 7: Tip: You may find it helpful to place the 1/2" Grommets 1" below the top edge, if you prefer a looser fit for the Gate Rings.

LST228 TOTO

  • (For Paper Pattern) Under FUSE INTERFACING TO COORDINATING PIECES
    • 1. ....Fabric Piece A Collar, with 1" on each end .....
    • 2. Join both Piece B by placing the short ends RST, perpendicular to each other. Sew a diagonal seam from corner to corner. Trim excess seam allowance to 1/4" wide. Press seam open
    • 3. Center and fuse Interfacing Piece B Leash to the WS of Main Fabric Piece B Leash, with 2-1/4" on each end with no interfacing. If using multiple pieces, position and fuse the first piece, then overlap the next piece 1/4" and fuse in place. (Figure 2)

LST230 REBECCA

  • There is an error in the CONTRAST Cutting Instructions. Piece E Vertical Borders should measure 1/2" wide by 9" high.

LST232 PHLOX

  • Page 2 under ADD EXTERIOR ZIPPER POCKET, Step 9: 'Piece X' should be Piece N.

LST237 FOGG

  • Main Fabric needed: 19" or 5/8" yard.

LST238 JOANNA

  • On page 1, under CUTTING INSTRUCTIONS: INTERFACING: Cut (2) .... Piece N.
  • On page 6, in the CUTTING LAYOUTS: Interfacing: adding a second Piece E.

LST239 EMMA

  • Make Pattern Piece F wider by drawing a line parallel and 3/8" from the long-angled edge (opposite the FOLD line).

LST240 SLOANE

  • Figure 4 should show the WS of Lining, not RS.
  • Page 3: Step 2 under ASSEMBLE EXTERIOR TOTE: ......Topstitch on RS of Piece E, 1/8" from seam, starting and ......
  • Please follow the illustration for Step 5 of placement of the handles under prepare and shape exterior. 
  • Figure 35 - 37 were mislabeled. Correction has been made.
  • Added 1/2" square to Page 6 for confirming printout is correct size.

LST243 VINNY

  • Please follow the illustration for Step 5 of placement of the handles under prepare and shape exterior.

LST247 STEWART

  • For 28" Sew-In-Foam - Cut 2 of Piece A with their longest edges parallel to the 18" [22-1/2"] edges of Foam.
  • CUTTING INSTRUCTIONS: HEAVY STABILIZER: Cut (1) ...... for Piece I (Base).

LST251 MUFFY

  • In the pattern text-- the first Step 2, should read On WS top 15" (or short) edge of Main Piece A... the figures are correct.
  • Back of pattern calls for 12" of lining, should be 13" - If you purchased 12" you could piece the lining to make the pocket piece.

LST253 THE MORNING POST

  • Disclaimer added for laptop size - "Size measured diagonally across screen".
  • Page 3, Under ASSEMBLE GUSSET: The Figure 16 illustration should be showing Piece D Zipper Gusset underneath the zipper.

LST256 SMITH

  • Link is no longer active for SEWINGONLINE.SULKY.COM.

LST257 ISIDORE

  • Figure 7 & 8 illustrations should show the interfacing side.
  • Figure 10 & 11 illustrations should not show the foam.
  • Typo on front cover fixed.